Notes on Use of Four-side Sealing Single PCS Wet Wipes Making Machine
Time: 0000-00-00 00:00:00
Notes on Use of Four-side Sealing Single PCS Wet Wipes Making Machine
In the process of long-term operation of wet wipes making machine, it is inevitable that some mechanical failures will occur,but don’t worry,following are some regular problem and the ways to repair:
1. If the speed of the four-side sealing wet wipes packing machine is too fast, the inner layer of the coating will have poor heat sealing.
If the temperature is too low, the seal will leak or become unstable.
The maintenance method is to slow down the speed, raise the temperature and replace the film material.
2. The solid state circuit breaker of the four-side seal wet wipes making machine is burnt out,temperature control instrument is damaged, thermocouple is damaged, thermometer cannot control temperature.The maintenance method is to replace the coupling, temperature control instrument and heating element.
3. The color of the film color code is too light, the film driver skids, and the color code trace is not turned on, and the cutting position will deviate from the color code.The maintenance method at this time is to refer to the packaging machine manual and adjust its sensitivity.In the man-machine dialogue interface, switch the tracking mode to "tracking switch".
4. The tool rest is too high or too low, and the packing speed is too fast.When the push rod and tool are out of sync, the tool will cut on the product.The maintenance method is to reduce the packing speed and adjust the height of the end sealing parts so that the center of the sealing knife is in the middle of the product height.
5. When the temperature of the four-side sealing wet wipes packing machine is too high, the speed is too slow, and the outer heat resistance of the envelope is poor, there will be scorching marks at the seal.
The maintenance method is to accelerate, cool and replace the film material.
6. When the air pressure is not right, the cylinder swing rod is loose, the heating temperature is low, the hot pressing roller and the driving roller are not parallel, and the heat sealing is bad.
The maintenance method is to adjust the parallelism, adjust the temperature and pressure so that they are parallel.
In the process of long-term operation of wet wipes making machine, it is inevitable that some mechanical failures will occur,but don’t worry,following are some regular problem and the ways to repair:
1. If the speed of the four-side sealing wet wipes packing machine is too fast, the inner layer of the coating will have poor heat sealing.
If the temperature is too low, the seal will leak or become unstable.
The maintenance method is to slow down the speed, raise the temperature and replace the film material.
2. The solid state circuit breaker of the four-side seal wet wipes making machine is burnt out,temperature control instrument is damaged, thermocouple is damaged, thermometer cannot control temperature.The maintenance method is to replace the coupling, temperature control instrument and heating element.
3. The color of the film color code is too light, the film driver skids, and the color code trace is not turned on, and the cutting position will deviate from the color code.The maintenance method at this time is to refer to the packaging machine manual and adjust its sensitivity.In the man-machine dialogue interface, switch the tracking mode to "tracking switch".
4. The tool rest is too high or too low, and the packing speed is too fast.When the push rod and tool are out of sync, the tool will cut on the product.The maintenance method is to reduce the packing speed and adjust the height of the end sealing parts so that the center of the sealing knife is in the middle of the product height.
5. When the temperature of the four-side sealing wet wipes packing machine is too high, the speed is too slow, and the outer heat resistance of the envelope is poor, there will be scorching marks at the seal.
The maintenance method is to accelerate, cool and replace the film material.
6. When the air pressure is not right, the cylinder swing rod is loose, the heating temperature is low, the hot pressing roller and the driving roller are not parallel, and the heat sealing is bad.
The maintenance method is to adjust the parallelism, adjust the temperature and pressure so that they are parallel.
Previous：What types of wet wipes? Next：The Advantages of Wet Wipes Machine